Pablo Neira Ayuso

pablo@netfilter.org

2008-2020 Pablo Neira Ayuso Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts, and no Back-Cover Texts. A copy of the license is included in the section entitled "GNU Free Documentation License". This document details how to install and to configure the conntrack-tools. This documentation provides a description on how to install and to configure the conntrack-tools. This documentation assumes that the reader is familiar with basic firewalling and Netfilter concepts. You also must understand the difference between stateless and stateful firewalls. Otherwise, please read Netfilter's Connection Tracking System published in :login; the USENIX magazine for a quick reference. The conntrack-tools package contains two programs: conntrack provides a full featured command line utility to interact with the connection tracking system. The conntrack utility provides a replacement for the limited /proc/net/nf_conntrack interface. With conntrack, you can list, update and delete the existing flow entries; you can also listen to flow events. conntrackd is the user-space connection tracking daemon. This daemon can be used to deploy fault-tolerant GNU/Linux firewalls but you can also use it to collect flow-based statistics of the firewall use. Mind the trailing d that refers to either the command line utility or the daemon. If you are using the Linux kernel that your distribution provides, then you most likely can skip this. If you compile your own Linux kernel, then please make sure the following options are enabled. You require a Linux kernel version >= 2.6.18. Connection Tracking System. CONFIG_NF_CONNTRACK=m CONFIG_NF_CONNTRACK_IPV4=m CONFIG_NF_CONNTRACK_IPV6=m (if your setup supports IPv6) nfnetlink: the generic messaging interface for Netfilter. CONFIG_NETFILTER_NETLINK=m nf_conntrack_netlink: the messaging interface for the Connection Tracking System. CONFIG_NF_CT_NETLINK=m connection tracking event notification API: the flow-based event notification interface. CONFIG_NF_CONNTRACK_EVENTS=y You can validate that your Linux kernel support for the conntrack-tools through modinfo. # modinfo nf_conntrack filename: /lib/modules/5.2.0/kernel/net/netfilter/nf_conntrack.ko license: GPL alias: nf_conntrack-10 alias: nf_conntrack-2 alias: ip_conntrack depends: nf_defrag_ipv6,libcrc32c,nf_defrag_ipv4 retpoline: Y intree: Y name: nf_conntrack vermagic: 5.7.0+ SMP preempt mod_unload modversions parm: tstamp:Enable connection tracking flow timestamping. (bool) parm: acct:Enable connection tracking flow accounting. (bool) parm: nf_conntrack_helper:Enable automatic conntrack helper assignment (default 0) (bool) parm: expect_hashsize:uint parm: enable_hooks:Always enable conntrack hooks (bool) Make sure nf_conntrack_netlink is also available. You also need to install the following library dependencies: libnfnetlink: the netfilter netlink library use the official release available in netfilter.org libnetfilter_conntrack: the netfilter netlink library use the official release available in netfilter.org Your distribution most likely also provides packages for this software, so you do not have to compile it yourself. To compile and install the conntrack-tools run the following commands: (non-root)$ tar xvjf conntrack-tools-x.x.x.tar.bz2 (non-root)$ cd conntrack-tools-x.x.x (non-root)$ ./configure --prefix=/usr (non-root)$ make (root) # make install Your distribution most likely also provides packages for this software, so you do not have to compile it yourself. The /proc/net/nf_conntrack interface is very limited as it only allows you to display the existing flows, their state and metadata such the flow mark: # cat /proc/net/nf_conntrack tcp 6 431982 ESTABLISHED src=192.168.2.100 dst=123.59.27.117 sport=34846 dport=993 packets=169 bytes=14322 src=123.59.27.117 dst=192.168.2.100 sport=993 dport=34846 packets=113 bytes=34787 [ASSURED] mark=0 use=1 tcp 6 431698 ESTABLISHED src=192.168.2.100 dst=123.59.27.117 sport=34849 dport=993 packets=244 bytes=18723 src=123.59.27.117 dst=192.168.2.100 sport=993 dport=34849 packets=203 bytes=144731 [ASSURED] mark=0 use=1 You can list the existing flows using the conntrack utility via -L command: # conntrack -L tcp 6 431982 ESTABLISHED src=192.168.2.100 dst=123.59.27.117 sport=34846 dport=993 packets=169 bytes=14322 src=123.59.27.117 dst=192.168.2.100 sport=993 dport=34846 packets=113 bytes=34787 [ASSURED] mark=0 use=1 tcp 6 431698 ESTABLISHED src=192.168.2.100 dst=123.59.27.117 sport=34849 dport=993 packets=244 bytes=18723 src=123.59.27.117 dst=192.168.2.100 sport=993 dport=34849 packets=203 bytes=144731 [ASSURED] mark=0 use=1 conntrack v1.4.6 (conntrack-tools): 2 flow entries have been shown. The conntrack syntax is similar to iptables. You can filter out the listing without using grep: # conntrack -L -p tcp --dport 993 tcp 6 431982 ESTABLISHED src=192.168.2.100 dst=123.59.27.117 sport=34846 dport=993 packets=169 bytes=14322 src=123.59.27.117 dst=192.168.2.100 sport=993 dport=34846 packets=113 bytes=34787 [ASSURED] mark=0 use=1 conntrack v1.4.6 (conntrack-tools): 1 flow entries have been shown. You can update the ct mark, extending the previous example: # conntrack -U -p tcp --dport 993 --mark 10 tcp 6 431982 ESTABLISHED src=192.168.2.100 dst=123.59.27.117 sport=34846 dport=993 packets=169 bytes=14322 src=123.59.27.117 dst=192.168.2.100 sport=993 dport=34846 packets=113 bytes=34787 [ASSURED] mark=10 use=1 conntrack v1.4.6 (conntrack-tools): 1 flow entries have been updated. You can also delete entries # conntrack -D -p tcp --dport 993 tcp 6 431982 ESTABLISHED src=192.168.2.100 dst=123.59.27.117 sport=34846 dport=993 packets=169 bytes=14322 src=123.59.27.117 dst=192.168.2.100 sport=993 dport=34846 packets=113 bytes=34787 [ASSURED] mark=10 use=1 conntrack v1.4.6 (conntrack-tools): 1 flow entries have been deleted. This allows you to block TCP traffic if: You have a stateful rule-set that drops traffic in INVALID state. You set /proc/sys/net/netfilter/nf_conntrack_tcp_loose to zero. You can also listen to the connection tracking events: # conntrack -E [NEW] udp 17 30 src=192.168.2.100 dst=192.168.2.1 sport=57767 dport=53 [UNREPLIED] src=192.168.2.1 dst=192.168.2.100 sport=53 dport=57767 [UPDATE] udp 17 29 src=192.168.2.100 dst=192.168.2.1 sport=57767 dport=53 src=192.168.2.1 dst=192.168.2.100 sport=53 dport=57767 [NEW] tcp 6 120 SYN_SENT src=192.168.2.100 dst=66.102.9.104 sport=33379 dport=80 [UNREPLIED] src=66.102.9.104 dst=192.168.2.100 sport=80 dport=33379 [UPDATE] tcp 6 60 SYN_RECV src=192.168.2.100 dst=66.102.9.104 sport=33379 dport=80 src=66.102.9.104 dst=192.168.2.100 sport=80 dport=33379 [UPDATE] tcp 6 432000 ESTABLISHED src=192.168.2.100 dst=66.102.9.104 sport=33379 dport=80 src=66.102.9.104 dst=192.168.2.100 sport=80 dport=33379 [ASSURED] There are many options, including support for XML output, more advanced filters, and so on. Please check the manpage for more information. The conntrackd daemon supports three modes: State table synchronization, to synchronize the connection tracking state table between several firewalls in High Availability (HA) scenarios. Userspace connection tracking helpers, for layer 7 Application Layer Gateway (ALG) such as DHCPv6, MDNS, RPC, SLP and Oracle TNS. As an alternative to the in-kernel connection tracking helpers that are available in the Linux kernel. Flow-based statistics collection, to collect flow-based statistics as an alternative to ulogd2, although ulogd2 allows for more flexible statistics collection. If you would like to configure conntrackd to work in state synchronization mode, then you require: A working installation of keepalived, preferibly a recent version. Check if your distribution comes with a recent packaged version. Otherwise, you may compile it from the sources. There is a very simple example file in the conntrackd sources to setup a simple HA cluster with keepalived (see the file keepalived.conf under the doc/sync/ directory). This file can be used to set up a simple VRRP cluster composed of two machines that hold the virtual IPs 192.168.0.100 on eth0 and 192.168.1.100 on eth1. If you are not familiar with keepalived, please read the official documentation available at the keepalived website (http://www.keepalived.org). If you use a different high availability manager, make sure it works correctly before going ahead. A dedicated link. The dedicated link between the firewalls is used to transmit and receive the state information. The use of a dedicated link is mandatory for security reasons as someone may pick the state information that is transfered between the firewalls. A well-formed stateful rule-set. Otherwise you are likely to experience problems during the fail-over. An example of a well-formed stateful iptables rule-set is available in the conntrack-tools website. If your Linux kernel is < 2.6.22, you have to disable TCP window tracking: # echo 1 > /proc/sys/net/netfilter/nf_conntrack_tcp_be_liberal The daemon conntrackd in synchronization mode supports up to three replication approaches: notrack: this approach is the most simple as it is based on a best effort replication protocol, ie. unreliable protocol. This protocol sends and receives the state information without performing any specific checking. ft-fw: this approach is based on a reliable protocol that performs message tracking. Thus, the protocol can recover from message loss, re-ordering and corruption. alarm: this approach is spamming. It is based on a alarm-based protocol that periodically re-sends the flow state to the backup firewall replicas. This protocol consumes a lot of bandwidth but it resolves synchronization problems fast. The three existing approaches are soft real-time asynchronous replication protocols that are aimed to have negligible impact in terms of latency and bandwidth throughput in the stateful firewall filtering. To configure conntrackd in any of the existing synchronization modes, you have to copy the example configuration file to the directory /etc/conntrackd/ on every firewall replica. Note that _type_ is the synchronization type selected. (conntrack-tools-x.x.x)# cp doc/_type_/conntrackd.conf /etc/conntrackd/conntrackd.conf Do not forget to edit the files before going ahead. There are several parameters that you have to tune to adapt the example configuration file to your setup. If you don't want to put the config file under /etc/conntrackd/, just tell conntrackd where to find it passing the option -C. A good reading to extend the information about firewall architectures is Demystifying cluster-based fault-tolerant firewalls published in IEEE Internet Computing magazine. In the Active-Backup setup, one of the stateful firewall replicas filters traffic and the other acts as backup. If you use this approach, you have to copy the script primary-backup.sh to: (conntrack-tools-x.x.x)# cp doc/sync/primary-backup.sh /etc/conntrackd/ The HA manager invokes this script when a transition happens, ie. If a stateful firewall replica: becomes active to recover the filtering. becomes backup. hits failure (this is available if the HA manager has a failure state, which is true for keepalived. The script is simple, and it contains the different actions that conntrackd performs to recover the filtering or purge obsolete entries from the state table, among others. The script is commented, you can have a look at it if you need further information. The Active-Active setup consists of having more than one stateful firewall actively filtering traffic. Thus, we reduce the resource waste that implies to have a backup firewall which is spare. We can classify the type of Active-Active setups in several families: Symmetric path routing: The stateful firewalls share the workload in terms of flows, ie. the packets that are part of a flow are always filtered by the same firewall. Asymmetric multi-path routing: The packets that are part of a flow can be filtered by whatever stateful firewall in the cluster. Thus, every flow-states have to be propagated to all the firewalls in the cluster as we do not know which one would be the next to filter a packet. This setup goes against the design of stateful firewalls as we define the filtering policy based on flows, not in packets anymore. conntrackd allows you to deploy an symmetric Active-Active setup based on a static approach. For example, assume that you have two virtual IPs, vIP1 and vIP2, and two firewall replicas, FW1 and FW2. You can give the virtual vIP1 to the firewall FW1 and the vIP2 to the FW2. The asymmetric path scenario is hard: races might occurs between state synchronization and packet forwarding. If you would like to deploy an Active-Active setup with an assymmetic multi-path routing configuration, then, make sure the same firewall forwards packets coming in the original and the reply directions. If you cannot guarantee this and you still would like to deply an Active-Active setup, then you might have to consider downgrading your firewall ruleset policy to stateless filtering. Once you have configured conntrackd, you can run in console mode which is an interactive mode, in that case type 'conntrackd' as root. (root)# conntrackd If you want to run conntrackd in daemon mode, then type: (root)# conntrackd -d You can verify that conntrackd is running by checking the log messages via ps. Moreover, if conntrackd is running fine, you can dump the current status of the daemon: # conntrackd -s cache internal: current active connections: 4 connections created: 4 failed: 0 connections updated: 0 failed: 0 connections destroyed: 0 failed: 0 cache external: current active connections: 0 connections created: 0 failed: 0 connections updated: 0 failed: 0 connections destroyed: 0 failed: 0 traffic processed: 0 Bytes 0 Pckts multicast traffic: 352 Bytes sent 0 Bytes recv 22 Pckts sent 0 Pckts recv 0 Error send 0 Error recv multicast sequence tracking: 0 Pckts mfrm 0 Pckts lost This command displays the number of entries in the internal and external cache: The internal cache contains the states that this firewall replica is filtering, ie. this is a cache of the kernel state table. The external cache contains the states that the other firewall replica is filtering. You can dump the internal cache with the following command: # conntrackd -i tcp 6 ESTABLISHED src=192.168.2.100 dst=139.174.175.20 sport=58491 dport=993 src=139.174.175.20 dst=192.168.2.100 sport=993 dport=58491 [ASSURED] mark=0 secmark=0 [active since 536s] tcp 6 ESTABLISHED src=192.168.2.100 dst=123.59.27.117 sport=38211 dport=993 src=123.59.27.117 dst=192.168.2.100 sport=993 dport=38211 [ASSURED] mark=0 secmark=0 [active since 536s] tcp 6 ESTABLISHED src=192.168.2.100 dst=123.59.27.117 sport=38209 dport=993 src=123.59.27.117 dst=192.168.2.100 sport=993 dport=38209 [ASSURED] mark=0 secmark=0 [active since 536s] tcp 6 TIME_WAIT src=192.168.2.100 dst=74.125.45.166 sport=42593 dport=80 src=74.125.45.166 dst=192.168.2.100 sport=80 dport=42593 [ASSURED] [active since 165s] tcp 6 ESTABLISHED src=192.168.2.100 dst=139.174.175.20 sport=37962 dport=993 src=139.174.175.20 dst=192.168.2.100 sport=993 dport=37962 [ASSURED] mark=0 secmark=0 [active since 536s] You can dump the external cache with the following command: # conntrackd -e If the replication works fine, conntrackd -s displays the active's internal cache should display the same number of entries than the backup's external cache and vice-versa. To verify that the recovery works fine, if you trigger a fail-over, the log files should display the following information: [Thu Sep 18 18:03:02 2008] (pid=9759) [notice] committing external cache [Thu Sep 18 18:03:02 2008] (pid=9759) [notice] Committed 1545 new entries This means that the state entries have been injected into the kernel correctly. The daemon allows several configuration options that you may want to enable. This section contains some information about them. It is possible to disable the external cache. Thus, conntrackd directly injects the flow-states into the in-kernel Connection Tracking System of the backup firewall. You can do it by enabling the DisableExternalCache option in the conntrackd.conf configuration file: Sync { Mode FTFW { [...] DisableExternalCache Off } } You can also use this option with the NOTRACK and ALARM modes. This increases CPU consumption in the backup firewall but now you do not need to commit the flow-states during the master failures since they are already in the in-kernel Connection Tracking table. Moreover, you save memory in the backup firewall since you do not need to store the foreign flow-states anymore. You can also disable the internal cache by means of the DisableInternalCache option in the conntrackd.conf configuration file: Sync { Mode NOTRACK { [...] DisableInternalCache Off } } However, this option is only available for the NOTRACK mode. This mode provides unreliable flow-state synchronization between firewalls. Thus, if flow-states are lost during the synchronization, the protocol provides no way to recover them. You can use up to three different transport layer protocols to synchronize flow-state changes between the firewalls: UDP, TCP and Multicast. UDP and multicast are unreliable but together with the FT-FW mode provide partial reliable flow-state synchronization. The preferred choice is FT-FW over UDP, or multicast alternatively. TCP introduces latency in the flow-state synchronization due to the congestion control. Under flow-state message are lost, the FIFO delivery becomes also a problem since the backup firewall quickly gets out of sync. For that reason, its use is discouraged. Note that using TCP only makes sense with the NOTRACK mode. You can set redundant dedicated links without using bonding, you have to configure as many redundant links as you want in the configuration file. In case of failure of the master dedicated link, conntrackd failovers to one of the backups. An example of this configuration is the following: Sync { Mode FTFW { [...] } # default master dedicated link UDP Default { IPv4_address 192.168.2.1 IPv4_Destination_Address 192.168.2.2 Port 3780 Interface eth3 SndSocketBuffer 24985600 RcvSocketBuffer 24985600 Checksum on } # backup dedicated link UDP { IPv4_address 192.168.1.3 IPv4_Destination_Address 192.168.1.4 Port 3780 Interface eth2 SndSocketBuffer 24985600 RcvSocketBuffer 24985600 Checksum on } [...] } Since Linux kernel >= 2.6.34, iptables provides the CT iptables target that allows to reduce the amount of Connection Tracking events that are delivered to user-space. However, you will have to use a Linux kernel >= 2.6.38 to profit from this feature, since several aspects of the event filtering were broken. The following example shows how to only generate the assured and destroy events: # iptables -I PREROUTING -t raw -j CT --ctevents assured,destroy One flow is assured if the firewall has seen traffic for it in both directions. Reducing the amount of events generated helps to reduce CPU consumption in the active firewall. The synchronization of expectations require a Linux kernel >= 3.5 to work appropriately. The connection tracking system provides helpers that allows you to filter multi-flow application protocols like FTP, H.323 and SIP among many others. These protocols usually split the control and data traffic in different flows. Moreover, the control flow usually announces layer 3 and 4 information to let the other peer know where the data flows will be open. This sort of protocols require that the firewall inspects the content of the packet, otherwise filtering by layer 3 and 4 selectors like addresses and ports become a real nightmare. Netfilter already provides the so-called helpers that track this protocol aspects to allow deploying appropriate filtering. These helpers create expectation entries that represent expected traffic that will arrive to the firewall according to the inspected packets. In case that you have enabled tracking of these protocols, you may want to enable the state-synchronization of expectation as well. Thus, established flows for this specific protocols will not suffer any disruption. To enable the expectation support in the configuration file, you have to use the following option: Sync { ... Options { ExpectationSync { ftp sip ras # for H.323 q.931 # for H.323 h.245 # for H.323 } } } The example above enables the synchronization of the expectations for the FTP, SIP and H.323 helpers. In my testbed, there are two firewalls in a primary-backup configuration running keepalived. They use a couple of floating cluster IP address (192.168.0.100 and 192.168.1.100) that are used by the client. These firewalls protect one FTP server (192.168.1.2) that will be accessed by one client. In ASCII art, it looks like this: 192.168.0.100 192.168.1.100 eth1 eth2 fw-1 / \ FTP client ------ ------ server 192.168.0.2 \ / 192.168.1.2 fw-2 This is the rule-set for the firewalls: -A FORWARD -m state --state RELATED -j ACCEPT -A FORWARD -i eth2 -m state --state ESTABLISHED -j ACCEPT -A FORWARD -i eth1 -p tcp -m tcp --dport 21 --tcp-flags FIN,SYN,RST,ACK SYN -m state --state NEW -j ACCEPT -A FORWARD -i eth1 -p tcp -m state --state ESTABLISHED -j ACCEPT -A FORWARD -m state --state INVALID -j LOG --log-prefix "invalid: " Before going ahead, make sure nf_conntrack_ftp is loaded. The following steps detail how to check that the expectation support works fine with FTP traffic: Switch to the client. Start one FTP control connection to one server that is protected by the firewalls, enter passive mode: (term-1) user@client$ nc 192.168.1.2 21 220 dummy FTP server USER anonymous 331 Please specify the password. PASS nothing 230 Login successful. PASV 227 Entering Passive Mode (192,168,1,2,163,11). This means that port 163*256+11=41739 will be used for the data traffic. I suggest you to read djb's FTP protocol description in case that you don't understand how this calculation is done. Switch to fw-1 (primary) to check that the expectation is in the internal cache. root@fw1# conntrackd -i exp proto=6 src=192.168.0.2 dst=192.168.1.2 sport=0 dport=41739 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=192.168.0.2 master-dst=192.168.1.2 sport=36390 dport=21 helper=ftp [active since 5s] Switch to fw-2 (backup) to check that the expectation has been successfully replicated. root@fw2# conntrackd -e exp proto=6 src=192.168.0.2 dst=192.168.1.2 sport=0 dport=41739 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=192.168.0.2 master-dst=192.168.1.2 sport=36390 dport=21 [active since 8s] Make the primary firewall fw-1 fail. Now fw-2 becomes primary. Switch to fw-2 (primary) to commit the external cache into the kernel. The logs should display that the commit was successful: root@fw2# tail -100f /var/log/conntrackd.log [Wed Dec 7 22:16:31 2011] (pid=19195) [notice] committing external cache: expectations [Wed Dec 7 22:16:31 2011] (pid=19195) [notice] Committed 1 new entries [Wed Dec 7 22:16:31 2011] (pid=19195) [notice] commit has taken 0.000366 seconds Switch to the client. Open a new terminal and connect to the port that has been announced by the server: (term-2) user@client$ nc -vvv 192.168.1.2 41739 (UNKNOWN) [192.168.1.2] 41739 (?) open Switch to term-1 and ask for the file listing: [...] 227 Entering Passive Mode (192,168,1,2,163,11). LIST Switch to term-2, it should display the listing. That means everything has worked fine. You may want to try disabling the expectation support and repeating the steps to check that it does not work without the state-synchronization. The user-space helper infrastructure requires a Linux kernel >= 3.6 to work appropriately. Connection tracking helpers allows you to filter multi-flow protocols that usually separate control and data traffic into different flows. These protocols usually violate network layering by including layer 3/4 details, eg. IP address and TCP/UDP ports, in their application protocol (which resides in layer 7). This is problematic for gateways since they operate at packet-level, ie. layers 3/4, and therefore they miss this important information to filter these protocols appropriately. Helpers inspect packet content (at layer 7) and create the so-called expectations. These expectations are added to one internal table that resides in the gateway. For each new packet arriving to the gateway, the gateway first looks up for matching expectations. If there is any, then this flow is accepted since it's been expected. Note this lookup only occurs for the first packet that is part of one newly established flow, not for all packets. Since 1.4.0, conntrackd provides the infrastructure to develop helpers in user-space. The main features of the user-space infrastructure for helpers are: Rapid connection tracking helper development, as developing code in user-space is usually faster. Reliability: A buggy helper does not crash the kernel. If the helper fails, ie. the conntrackd crashes, Moreover, we can monitor the helper process and restart it in case of problems. Security: Avoid complex string matching and mangling in kernel-space running in privileged mode. Going further, we can even think about running user-space helper as a non-root process. It allows the development of very specific helpers for proprietary protocols that are not standard. This is the case of the SQL*net helper. Implementing this in kernel-space may be problematic, since this may not be accepted for ainline inclusion in the Linux kernel. As an alternative, we can still distribute this support as separate patches. However, my personal experience is that, given that the kernel API/ABI is not stable, changes in the interface lead to the breakage of the patch. This highly increase the overhead in the maintainance. Currently, the infrastructure supports the following user-space helpers: Oracle*TNS, to support its special Redirect message. NFSv3, mind that version 4 does not require this helper. FTP (this helper is also available in kernel-space). SSDP. The following steps describe how to enable the RPC portmapper helper for NFSv3 (this is similar for other helpers): Register user-space helper: nfct add helper rpc inet udp nfct add helper rpc inet tcp This registers the portmapper helper for both UDP and TCP (NFSv3 traffic goes both over TCP and UDP). Add iptables rule using the CT target: # iptables -I OUTPUT -t raw -p udp --dport 111 -j CT --helper rpc # iptables -I OUTPUT -t raw -p tcp --dport 111 -j CT --helper rpc With this, packets matching port TCP/UDP/111 are passed to user-space for inspection. If there is no instance of conntrackd configured to support user-space helpers, no inspection happens and packets are not sent to user-space. Add configuration to conntrackd.conf: Helper { Type rpc inet udp { QueueNum 1 QueueLen 10240 Policy rpc { ExpectMax 1 ExpectTimeout 300 } } Type rpc inet tcp { QueueNum 2 QueueLen 10240 Policy rpc { ExpectMax 1 ExpectTimeout 300 } } } This configures conntrackd to use NFQUEUE queue numbers 1 and 2 to send traffic for inspection to user-space Make sure your queue numbers do not collide with those used in your conntrackd.conf file. Now you can test this (assuming you have some working NFSv3 setup) with: mount -t nfs -onfsvers=3 mynfs.server.info:/srv/cvs /mnt/ You should see new expectations being added via: # conntrack -E expect [NEW] 300 proto=17 src=1.2.3.4 dst=1.2.3.4 sport=0 dport=54834 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=1.2.3.4 master-dst=1.2.3.4 sport=58190 dport=111 PERMANENT class=0 helper=rpc [NEW] 300 proto=6 src=1.2.3.4 dst=1.2.3.4 sport=0 dport=2049 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=1.2.3.4 master-dst=1.2.3.4 sport=55450 dport=111 PERMANENT class=0 helper=rpc [NEW] 300 proto=17 src=1.2.3.4 dst=1.2.3.4 sport=0 dport=58031 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=1.2.3.4 master-dst=1.2.3.4 sport=56309 dport=111 PERMANENT class=0 helper=rpc Problems with conntrackd? The following list of questions should help for troubleshooting: I see packets lost in conntrackd -s You can rise the value of McastRcvSocketBuffer and McastRcvSocketBuffer, if the problem is due to buffer overruns in the multicast sender or the receiver, the problem should disapear. The log messages report that the maximum netlink socket buffer has been reached. You can increase the values of SocketBufferSize and SocketBufferSizeMaxGrown. I see can't open multicast server in the log messages Make sure that the IPv4_interface clause has the IP of the dedicated link. Can I use wackamole, heartattack or any other HA manager? Absolutely, you can. But before reporting issues, make sure that your HA manager is not the source of the problems. Does conntrackd support TCP flow-recovery with window tracking enabled? Yes, but you require a Linux kernel >= 2.6.36 and the conntrack-tools >= 0.9.15. To enable it, check the TCPWindowTracking clause in the example configuration files. Does conntrackd support the H.323 and SIP connection tracking helpers? Yes, conntrackd includes expectation support since version 1.2.0. Is there any way to set up a more verbose mode in the log message for debugging? No, but conntrackd provides lots of information that you can look up in runtime via -s option. You can check network statistics to find anomalies: # conntrackd -s network network statistics: recv: Malformed messages: 0 Wrong protocol version: 0 Malformed header: 0 Malformed payload: 0 Bad message type: 0 Truncated message: 0 Bad message size: 0 send: Malformed messages: 0 sequence tracking statistics: recv: Packets lost: 42726 Packets before: 0 UDP traffic (active device=eth3): 564232 Bytes sent 1979844 Bytes recv 2844 Pckts sent 8029 Pckts recv 0 Error send 0 Error recv You can check cache statistics: # conntrackd -s cache cache:internal active objects: 0 active/total entries: 0/ 0 creation OK/failed: 11068/ 0 no memory available: 0 no space left in cache: 0 update OK/failed: 4128/ 0 entry not found: 0 deletion created/failed: 11068/ 0 entry not found: 0 cache:external active objects: 0 active/total entries: 0/ 0 creation OK/failed: 10521/ 0 no memory available: 0 no space left in cache: 0 update OK/failed: 8832/ 0 entry not found: 0 deletion created/failed: 10521/ 0 entry not found: 0 You can check runtime miscelaneous statistics: # conntrackd -s runtime daemon uptime: 14 min netlink stats: events received: 24736 events filtered: 0 events unknown type: 0 catch event failed: 0 dump unknown type: 0 netlink overrun: 0 flush kernel table: 1 resync with kernel table: 0 current buffer size (in bytes): 8000000 runtime stats: child process failed: 0 child process segfault: 0 child process termsig: 0 select failed: 0 wait failed: 0 local read failed: 0 local unknown request: 0 You can check dedicated link statistics: # conntrackd -s link UDP traffic device=eth3 status=RUNNING role=ACTIVE: 566848 Bytes sent 1982612 Bytes recv 3018 Pckts sent 8203 Pckts recv 0 Error send 0 Error recv You can check network queue statistics: # conntrackd -s queue allocated queue nodes: 1 queue txqueue: current elements: 0 maximum elements: 2147483647 not enough space errors: 0 queue errorq: current elements: 0 maximum elements: 128 not enough space errors: 0 queue rsqueue: current elements: 1 maximum elements: 131072 not enough space errors: 0 You may want to integrate conntrackd into your system in order to build a robust firewall cluster. You should take a look at how the linux distro of your choice does this, as there are some interesting things to take into account. Depending on the architecture of the firewall cluster, you may want to sync each node after a fallback operation, so the new node inmediately knows the connection of the other. This is specially interesting in Active-Active mode. This can be done using conntrackd -n just after the new node has joined the conntrackd cluster, for example at boot time. These operations require the main conntrackd daemon to open the UNIX socket to receive the order from the conntrackd -n call. Care must be taken that no race conditions happens (i.e, the UNIX socket is actually opened before conntrackd -n is launched). Otherwise, you may end with a new node (after fallback) which doesn't know any connection states from the other node. Since conntrack-tools 1.4.4, the conntrackd daemon includes integration with libsystemd. If conntrackd is configured at build time with this support (using --enable-systemd), then you can use Systemd on in the conntrackd.conf main configuration file. To benefit from this integration, you should use a systemd service file of Type=notify, which also includes support for the systemd watchdog. Using systemd and conntrackd with libsystemd support and a service file of Type=notify means that conntrackd will notify of its readiness to systemd, so you can launch conntrackd -n safely, avoiding such race conditions.