# # Synchronizer settings # Sync { Mode NOTRACK { # # Entries committed to the connection tracking table # starts with a limited timeout of N seconds until the # takeover process is completed. # CommitTimeout 180 } # # Multicast IP and interface where messages are # broadcasted (dedicated link). IMPORTANT: Make sure # that iptables accepts traffic for destination # 225.0.0.50, eg: # # iptables -I INPUT -d 225.0.0.50 -j ACCEPT # iptables -I OUTPUT -d 225.0.0.50 -j ACCEPT # Multicast { IPv4_address 225.0.0.50 IPv4_interface 192.168.100.100 # IP of dedicated link Interface eth2 Group 3780 # The multicast sender uses a buffer to enqueue the packets # that are going to be transmitted. The default size of this # socket buffer is available at /proc/sys/net/core/wmem_default. # This value determines the chances to have an overrun in the # sender queue. The overrun results packet loss, thus, losing # state information that would have to be retransmitted. If you # notice some packet loss, you may want to increase the size # of the sender buffer. Note: This protocol is best effort, # really recommended to increase the buffer size. McastSndSocketBuffer 1249280 # The multicast receiver uses a buffer to enqueue the packets # that the socket is pending to handle. The default size of this # socket buffer is available at /proc/sys/net/core/rmem_default. # This value determines the chances to have an overrun in the # receiver queue. The overrun results packet loss, thus, losing # state information that would have to be retransmitted. If you # notice some packet loss, you may want to increase the size of # the receiver buffer. Note: This protocol is best effort, # really recommended to increase the buffer size. McastRcvSocketBuffer 1249280 } # Enable/Disable message checksumming Checksum on # Uncomment this if you want to replicate just certain TCP states. # This option introduces a tradeoff in the replication: it reduces # CPU consumption and lost messages rate at the cost of having # backup replicas that don't contain the current state that the active # replica holds. TCP states are: SYN_SENT, SYN_RECV, ESTABLISHED, # FIN_WAIT, CLOSE_WAIT, LAST_ACK, TIME_WAIT, CLOSE, LISTEN. # # Replicate ESTABLISHED TIME_WAIT for TCP # If you have a multiprimary setup (active-active) without connection # persistency, ie. you can't know which firewall handles a packet # that is part of a connection, then you need direct commit of # conntrack entries to the kernel conntrack table. OSPF setups must # set on this option. Default is Off. # # CacheWriteThrough On } # # General settings # General { # # Number of buckets in the caches: hash table # HashSize 8192 # # Maximum number of conntracks: # it must be >= $ cat /proc/sys/net/ipv4/netfilter/ip_conntrack_max # HashLimit 65535 # # Logfile: on, off, or a filename # Default: on (/var/log/conntrackd.log) # #LogFile off # # Syslog: on, off or a facility name (daemon (default) or local0..7) # Default: off # #Syslog on # # Lockfile # LockFile /var/lock/conntrack.lock # # Unix socket configuration # UNIX { Path /tmp/sync.sock Backlog 20 } # # Netlink socket buffer size # SocketBufferSize 262142 # # Increase the socket buffer up to maximum if required # SocketBufferSizeMaxGrown 655355 # # Event filtering: This clause allows you to filter certain traffic, # There are currently three filter-sets: Protocol, Address and # State. The filter is attached to an action that can be: Accept or # Ignore. Thus, you can define the event filtering policy of the # filter-sets in positive or negative logic depending on your needs. # Filter { # # Accept only certain protocols: You may want to replicate # the state of flows depending on their layer 4 protocol. # Protocol Accept { TCP } # # Ignore traffic for a certain set of IP's: Usually all the # IP assigned to the firewall since local traffic must be # ignored, only forwarded connections are worth to replicate. # Address Ignore { IPv4_address 127.0.0.1 # loopback IPv4_address 192.168.0.1 IPv4_address 192.168.1.1 IPv4_address 192.168.100.100 # dedicated link ip IPv4_address 192.168.0.100 # virtual IP 1 IPv4_address 192.168.1.100 # virtual IP 2 } # # Uncomment this line below if you want to filter by flow state. # This option introduces a trade-off in the replication: it # reduces CPU consumption at the cost of having lazy backup # firewall replicas. The existing TCP states are: SYN_SENT, # SYN_RECV, ESTABLISHED, FIN_WAIT, CLOSE_WAIT, LAST_ACK, # TIME_WAIT, CLOSED, LISTEN. # # State Accept { # ESTABLISHED CLOSED TIME_WAIT CLOSE_WAIT for TCP # } } }